Eaglerise LED Drivers Philippines

Specification rules

Three rules we design to

These are not preferences. They are the constraints that decide whether a scheme commissions cleanly or comes back as a warranty claim, and we apply them to every driver schedule we issue.

1.25×

Size at 1.25× connected load

A 100W run takes a 125W driver or larger. The headroom keeps the unit off its thermal ceiling, where efficiency drops and life shortens.

160W

The 12V ceiling

160W is the largest 12V constant voltage driver in the range. Runs above it split across two drivers — plan the feed positions at design stage, not on site.

24V

Dim at 24V, not 12V

There is no dimmable 12V constant voltage driver and no Triac constant voltage driver in the range. If the run must dim, specify 24V with 0-10V or DALI-2.

Catalogue page references below point to the Eaglerise Indoor LED Driver Catalogue 2026. Stock position and lead time are confirmed on enquiry — tell us the run length, voltage and control protocol and we will return the driver schedule.

Constant voltage

CV drivers — strip, Neonflex, magnetic track

Fixed 12V, 24V or 48V output. Specify against the total connected load of the run, at 1.25× and within the voltage ceiling. For the strip these feed, see our LED strip lights range.

Slim LS

The general-purpose constant-voltage range. IP20, on/off, for concealed strip runs and magnetic track feeds.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-30-12 LI EXC	30W	12V · 0–2.5A	87%	0.95	136 × 38 × 28mm	IP20	On/off	p.102
Class I/II, SELV, OTP. Ta 45°C / Tc 85°C.
LS-60-12 LI EXC	60W	12V · 0–5A	88%	0.95	168 × 38 × 30mm	IP20	On/off	p.102
Class I/II, SELV, OTP. Ta 45°C / Tc 85°C.
LS-150-24 LI EXC	150W	24V · 0–6.25A	93%	0.95	227 × 38 × 30mm	IP20	On/off	p.102
24V standardised on 150W and 250W. Ta 45°C / Tc 85°C.
LS-250-24 LI EXC	250W	24V · 0–10.4A	93%	0.95	318 × 45 × 30mm	IP20	On/off	p.102
318mm long — verify the housing before specifying.
LS-150-48 LI EXC	150W	48V · 0–3.13A	93%	0.95	227 × 38 × 30mm	IP20	On/off	p.102
48V for magnetic track runs up to ~120W at 80% loading.
LS-250-48 LI EXC	250W	48V · 0–5.2A	93%	0.95	318 × 45 × 30mm	IP20	On/off	p.102
48V for magnetic track runs up to ~200W at 80% loading.

Ultrathin US

17–18mm high, for shallow ceiling voids and slim profiles where an LS body will not sit.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
US-100-12 LI EXC S	100W	12V · 0–8.33A	91%	0.95	177 × 56.4 × 17.2mm	IP20	On/off	p.105
17mm height suits profiles. No 100W in the slim LS 12V line, so this is the matching model.
US-150-12 LI EXC S	150W	12V · 0–11A	92%	0.95	177 × 56.4 × 17.2mm	IP20	On/off	p.105
Highest 12V IP20 in the range. Indoor alternative where the IP67 160W is oversize.

IP67 VTS

Eaglerise VTS IP67 constant voltage LED driver, sealed housing with pre-fitted input and output leads

Fully potted and sealed. Specify for exterior coves, soffits, landscape and wet areas.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
VTS-24-12 IP67 L	24W	12V · 0–2A	86%	0.95	118 × 35 × 26mm	IP67	On/off	p.107
Smallest sealed unit. Ta 45°C / Tc 80°C.
VTS-40-12 IP67 L	40W	12V · 0–3.34A	86%	0.95	148 × 42 × 30mm	IP67	On/off	p.107
Sealed IP67 housing. Class I/II, SELV.
VTS-60-12 IP67 L	60W	12V · 0–5A	86.5%	0.95	162 × 42 × 32mm	IP67	On/off	p.107
Sealed IP67 housing — verify fit in shallow outdoor fixtures.
VTS-100-12 IP67 L	100W	12V · 0–8.33A	87%	0.95	190 × 52 × 33mm	IP67	On/off	p.107
Sealed IP67 housing. Class I/II, SELV.
VTS-160-12 IP67 L	160W	12V · 0–13.3A	91%	0.95	190 × 52 × 37.5mm	IP67	On/off	p.107
The 12V ceiling. One SKU covers indoor and outdoor 12V high-power. Runs above 160W split across two drivers.
VTS-60-24 IP67 L	60W	24V · 0–2.5A	89%	0.95	162 × 42 × 32mm	IP67	On/off	p.107
Sealed IP67 housing. Ta 45°C / Tc 80°C.
VTS-160-24 IP67 L	160W	24V · 0–6.67A	92%	0.95	190 × 52 × 37.5mm	IP67	On/off	p.107
Sealed IP67 housing. Ta 45°C / Tc 80°C.
VTS-160-48 IP67 L	160W	48V · 0–3.33A	92%	0.95	190 × 52 × 37.5mm	IP67	On/off	p.107
48V sealed unit for exterior magnetic track.

MH switch PSU

Eaglerise MH switch-mode LED power supply, vented metal case with screw terminal block

Metal-cased switch-mode supply with a wide 100–240V input — the range to specify where mains regulation is poor.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
MH-200-48 LI	200W	48V · 0–4.17A	92.5%	0.9	195 × 55 × 27mm	IP20	On/off	p.108
Wide 100–240V input — the exception for sites with poor regulation. Ta 70°C / Tc 90°C.
MH-300-48 LI	300W	48V · 0–6.25A	93%	0.9	224 × 62 × 32mm	IP20	On/off	p.108
Higher-capacity 48V for longer magnetic track runs.

DALI-2 CV

Constant voltage with DALI-2 addressable control for strip integrated into a building control system.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-150-24 DALI-2 LI1	150W	24V · 0–6.25A	91%	0.95	318 × 38 × 30mm	IP20	DALI-2	p.98
DALI, push and corridor mode. DALI-2 parts 251/252/253. Ta 45°C / Tc 85°C.
LS-250-24 DALI-2 LI	250W	24V · 0–10.41A	91%	0.95	431 × 45 × 30mm	IP20	DALI-2	p.98
DALI, push and corridor mode.

0-10V CV

Eaglerise LS 0-10V dimmable constant voltage LED driver, 24V output

Constant voltage with 0-10V, RX and PWM dimming for analogue control lines.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-150-24 0-10 LI	150W	24V · 0–6.25A	92%	0.95	318 × 38 × 30mm	IP20	0-10V	p.100
0-10V, RX and PWM. No Triac — acceptable for BMS-controlled projects.
LS-250-24 0-10 LI	250W	24V · 0–10.41A	91%	0.95	431 × 45 × 30.5mm	IP20	0-10V	p.100
0-10V, RX and PWM dimming. 431mm long — verify the housing.

DALI-2 + 0-10V

Eaglerise VTS-200-24 DALI-2 and 0-10V IP65 constant voltage LED driver with marked input and output leads

Dual-protocol constant voltage, IP65, for exterior runs that must also be dimmed.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
VTS-200-24 DALI-2 0-10 IP65 L	200W	24V · 0–8.33A	91%	0.95	350 × 45 × 33mm	IP65	DALI-2	p.96
The only CV above 160W. DALI, push, 0-10V, PWM and RX. Reference only.

Constant current

CC drivers — downlights, spots, modules

Fixed output current with the voltage floating across the array's forward voltage. Match the drive current to the module and confirm the forward voltage range falls inside the driver's window.

Compact SI2 E

Low power factor, flicker-free constant current for downlights and MR16 modules. ErP 2.0 compliant.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-8-160…220 SI2 E	8W	160 / 180 / 200 / 220mA @ 30–40V	80%	0.60	92 × 28 × 21mm	IP20	On/off	p.54
Fits a 35mm aperture. ErP 2.0 compliant, flicker-free.
LS-12-250 SI2 E	12W	250mA @ 30–40V	82%	0.60	92 × 28 × 21mm	IP20	On/off	p.54
Fits a 35mm aperture. ErP 2.0 compliant, flicker-free.
LS-12-350 SI2 E	12W	350mA @ 30–40V	82%	0.60	92 × 28 × 21mm	IP20	On/off	p.54
Fits a 35mm aperture. ErP 2.0 compliant, flicker-free.

Compact LI2 EXC

The high power-factor (0.95) constant-current option — specify where PF is a project requirement.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-8-160 LI2 EXC	8W	160mA @ 27–42V	75%	0.95	92 × 36 × 25mm	IP20	On/off	p.56
Power factor 0.95 version of the 160mA unit — specify where PF is required.
LS-15-350 LI2 EXC	15W	350mA @ 27–42V	82%	0.95	92 × 36 × 25mm	IP20	On/off	p.56
LS-21-500 LI2 EXC	21W	500mA @ 27–42V	86%	0.95	102 × 38.2 × 25mm	IP20	On/off	p.56

Compact Triac

Eaglerise LS TRIAC LI1 constant current LED driver, phase-dimmable, with grey end caps

Constant current dimmable from standard leading- and trailing-edge phase dimmers.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
LS-12-250 TRIAC LI EXC	12W	250mA @ 27–40V	83%	0.9	115 × 30 × 20.5mm	IP20	Triac	p.43
Leading and trailing edge. Ta 50°C / Tc 85°C.
LS-12-350 TRIAC LI EXC	12W	350mA @ 27–40V	83%	0.9	115 × 30 × 20.5mm	IP20	Triac	p.43
Leading and trailing edge.
LS-15-500 TRIAC LI1	15W	500mA @ 20–30V	82%	0.95	102 × 38.2 × 25mm	IP20	Triac	p.46
LS-20-550 TRIAC LI1	20W	550mA @ 28–38V	85%	0.95	102 × 38.2 × 25mm	IP20	Triac	p.46
LS-30-700 TRIAC LI1	30W	700mA @ 28–42V	86%	0.95	135 × 41 × 25mm	IP20	Triac	p.47

Mini 0-10V

Compact constant current with 0-10V dimming, 1%–100%.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
FLS-20-500 0-10 LD ADV	20W	350–500mA (dip) @ 24–42V	86%	0.95	98 × 43 × 22mm	IP20	0-10V	p.78
Dip-switch current. 1–100% dimming.
FLS-30-700 0-10 LD ADV	30W	550–700mA (dip) @ 24–42V	87%	0.95	113 × 43 × 25mm	IP20	0-10V	p.78

Mini DALI-2

Compact constant current with DALI-2 addressable dimming, 1%–100%.

Model	Power	Output	Efficiency	PF	Dimensions (L × W × H)	IP	Control	Cat.
FLS-20-500 DALI-2 LD PRO	20W	80–500mA (dip) @ 2.5–49V	87%	0.95	88 × 40 × 22mm	IP20	DALI-2	p.75
DALI, push, corridor. 22mm height.
FLS-30-700 DALI-2 LD PRO	30W	150–700mA (dip) @ 2.5–49V	90%	0.95	98 × 43 × 22mm	IP20	DALI-2	p.75
FLS-42-1050 DALI-2 LD PRO	42W	300–1050mA (dip) @ 2.5–49V	90%	0.95	98 × 43 × 22mm	IP20	DALI-2	p.75

FAQ

Frequently Asked Questions

How do I size an LED driver?

Total the connected load, then specify a driver rated at least 1.25 times that figure — a 100W run wants a 125W driver or larger. The 25% headroom keeps the driver off its thermal ceiling, which is where efficiency falls and life shortens. Every Eaglerise unit we specify carries over-temperature protection with a published maximum ambient of 45°C and case temperature of 80–85°C, but headroom at design stage is what stops you relying on it.

What is the difference between constant voltage and constant current?

A constant voltage driver holds a fixed output voltage — 12V, 24V or 48V — and the load draws whatever current it needs. That is what LED strip, Neonflex and magnetic track are built for. A constant current driver holds a fixed current, typically 160mA to 1050mA, and lets the voltage float across the forward voltage of the array. That is what downlights, spots and MR16 modules need. They are not interchangeable: putting a strip on a constant current driver, or a module on constant voltage, damages the load.

Can I dim a 12V LED strip with an Eaglerise driver?

No. Eaglerise makes no dimmable 12V constant voltage driver and no Triac constant voltage driver at any voltage. If the run must dim, specify 24V, where 0-10V and DALI-2 are both available — for example the LS-150-24 0-10 LI at 150W, or the LS-150-24 DALI-2 LI1. If the design is fixed at 12V and must dim from a wall dimmer, that driver has to come from another manufacturer. We would rather tell you at specification stage than at commissioning.

What does IP67 mean for a driver?

IP67 is total protection against dust and against immersion in water to one metre for thirty minutes. In practice it means the driver body is potted and can sit in an exterior cove, a soffit or a landscape enclosure without a separate weatherproof box. Our sealed range is the VTS series, from the 24W VTS-24-12 up to the 160W VTS-160-12, VTS-160-24 and VTS-160-48. IP20 units carry no such protection and are strictly indoor, in a dry, ventilated void.

Why do you specify Eaglerise?

Eaglerise is a Shenzhen-listed manufacturer (stock code 002922) established in 1999, holding over 300 patents, with CE and CB certification across the range and a five-year warranty. For a specifier the practical points are the published thermal data — every series states its maximum ambient and case temperature and carries over-temperature protection — and the fact that a listed manufacturer can still be held to a warranty in year four.

EagleriseLED Drivers